夜雨聆风学习资料网

ARTICLE · 1360028

国外标准翻译-加拿大标准文件电子版下载 CSA B137-2026【PDF原文+中文翻译版】热塑性压力管道标准套装-包含全部 CSA B137最新版系列标准

国外标准翻译-加拿大标准文件电子版下载 CSA B137-2026【PDF原文+中文翻译版】热塑性压力管道标准套装-包含全部 CSA B137最新版系列标准

CSA B137:26 SERIES PACKAGE-2026【PDF原文+中文翻译版】

Thermoplastic Pressure Piping Standards Package - Consists of all the CSA B137:26 standards

standard by Canadian Standards Association, 04/07/2026.

LANGUAGES: English+Chinese【英文原文+中文翻译】

Historical Editions: CSA B137:23 SERIES PACKAGE, CSA B137:20 SERIES PACKAGE, CAN/CSA B137 SERIES-17, CAN/CSA B137 SERIES-13 (R2016), CSA B137 SERIES-09, CSA B137 SERIES-05, CAN/CSA B137 SERIES-02, CSA B137.9-99, CSA B137.4-99, CSA B137.4.1-99, CSA B137.3-99, CSA B137.8-99, CSA B137.2-99, CSA B137.12-99, CSA B137.10-99, CSA B137.0-99

Description

Thermoplastic Pressure Piping Standards Package consists of:

CSA B137.0:26 - Definitions, general requirements, and methods of testing for thermoplastic pressure piping

Preface

This is the thirteenth edition of CSA B137.0, Definitions, general requirements, and methods of testing for thermoplastic pressure piping. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1993, 1986, 1981, and 1973.

CSA B137.0 provides requirements and test methods that are common to some or all of the Standards of the CSA B137 Series. Wherever possible, individual Standards make reference to the relevant clauses in CSA B137.0.

The following are the major changes to this edition:

a) revision to Clause 1.1 notes;

b) revision to the verification procedure for hydrostatic design basis–rated compounds; and

c) deletion of table for preferred numbers in the R10 series from Annex A.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.1:26 - Polyethylene (PE) pipe, tubing, and fittings for cold-water pressure services

Preface

This is the thirteenth edition of CSA B137.1, Polyethylene (PE) pipe, tubing, and fittings for cold-water pressure services. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1995, 1989, 1983, and 1970.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) revision to the applications in the scope;

b) revision to Clause 4.2.2 for basic properties;

c) new clause for colour code E compounds;

d) new clause for workmanship;

e) removal of the hydrostatic sustained pressure strength, Kellam stress-cracking, and apparent tensile strength tests;

f) addition of sustained pressure and tensile strength tests;

g) revision to ductility requirements;

h) addition of carbon black and colourant requirements;

i) addition of the following fitting types: plastic socket-type fusion, plastic moulded fusion, plastic fabricated, and plastic electrofusion;

j) revision to potable water application requirements, including markings;

k) addition of dimensional requirements for DR-based DIOD-sized PE pipe; and

l) revision to working pressure and working temperature requirements.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.2:26 - Polyvinylchloride (PVC) injection-moulded gasketed fittings for pressure applications

Preface

This is the eleventh edition of CSA B137.2, Polyvinylchloride (PVC) injection-moulded gasketed fittings for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1993, and 1989.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major change to this edition is a revision to the long-term hydrostatic strength requirements.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.3:26 - Rigid polyvinylchloride (PVC) pipe and fittings for pressure applications

Preface

This is the fifteenth edition of CSA B137.3, Rigid polyvinylchloride (PVC) pipe and fittings for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1993, 1990, 1986, 1981, 1972, and 1970.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major change to this edition is a correction to the nominal pipe size in Table 15 from 7 to 8.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.3.1:26 - Molecularly oriented polyvinylchloride (PVCO) pipe for pressure applications

Preface

This is the sixth edition of CSA B137.3.1, Molecularly oriented polyvinylchloride (PVCO) pipe for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, 2013, and 2009.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major change to this edition is updating the reference of CSA B137.0 to the 2026 edition.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.4:26 - Polyethylene (PE) piping systems for gas services

Preface

This is the thirteenth edition of CSA B137.4, Polyethylene (PE) piping systems for gas services. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1992, 1986, 1977, and 1971.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) clarification of the scope of the standard; and

b) revision to the elevated temperature sustained pressure test requirements for PE pipe or tubing and addition of retest requirements.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.4.1:26 - Electrofusion-type polyethylene (PE) fittings for gas services

Preface

This is the tenth edition of CSA B137.4.1, Electrofusion-type polyethylene (PE) fittings for gas services, which supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, and 1989.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major change in this edition is updating the test name from ""single-point elevated temperature pressure test"" to ""elevated temperature sustained pressure test"" for consistency with CSA B137.4.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.5:26 - Crosslinked polyethylene (PEX) tubing systems for pressure applications

Preface

This is the twelfth edition of CSA B137.5, Crosslinked polyethylene (PEX) tubing systems for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1997, 1996, and 1989.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major changes to this edition include

a) revision to applications in the scope;

b) addition of requirements for pipe with an optional oxygen barrier layer;

c) addition of requirements for pipe with a mid-wall barrier layer;

d) addition of PEX XX07 designation code;

e) addition of requirements for sulfone plastic, polyvinylidene fluoride, and polyphenylene sulfide plastic fittings and components;

f) clarification of testing for minimum crosslinking value;

g) revision to excessive temperature and pressure capability test requirement;

h) revision to oxidative stability in potable chlorinated water applications requirement;

i) addition of requirements for UV resistance in potable water applications, hydrostatic burst pressure, and adhesion test;

j) clarification of the bent-tube hydrostatic sustained pressure strength test procedure;

k) update to storage and handling and protection from short- and long-term exposure to sunlight in Annex A;

l) changing hydrostatic design requirements from hydrostatic design stresses to hydrostatic design bases; and

m) addition of two hydrostatic design basis values for 23 °C.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standard Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.6:26 - Chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings for hot-and cold-water distribution systems

Preface

This is the twelfth edition of CSA B137.6, Chlorinated polyvinylchloride (CPVC) pipe, tubing, and fittings for hot- and cold-water distribution systems. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1996, 1983, and 1971.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major changes to this edition include

a) revision to the pressure rating requirements; and

b) addition of Schedule 40 pipe and fitting dimensions.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.9:26 - Polyethylene/aluminum/polyethylene (PE-AL-PE) composite pressure-pipe systems

Preface

This is the eleventh edition of CSA B137.9, Polyethylene/aluminum/polyethylene (PE-AL-PE) composite pressure-pipe systems. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1998, and 1991.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major change in this new edition is a revision to the stress/rupture lifetime requirement.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.10:26 - Crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) composite pressure-pipe systems

Preface

This is the eleventh edition of CSA B137.10, Crosslinked polyethylene/aluminum/crosslinked polyethylene (PEX-AL-PEX) composite pressure-pipe systems. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, 1998, and 1991.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) revision to applications in the scope; and

b) revision to excessive temperature and pressure capability test.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.11:26 - Polypropylene (PP-R & PP-RCT) pipe and fittings for pressure applications

Preface

This is the tenth edition of CSA B137.11, Polypropylene (PP-R and PP-RCT) pipe and fittings for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, and 1993.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) revision to the applications in the scope; and

b) addition of requirements for the impact resistance of pipe.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.12:26 - Polyamide (PA) piping systems for gas services

Preface

This is the tenth edition of CSA B137.12, Polyamide (PA) piping systems for gas services. It supersedes the previous editions published in 2023, 2020, 2017, 2013, 2009, 2005, 2002, 1999, and 1996.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) addition of requirements for PA423 (i.e., polyamide-12 or PA12) compounds;

b) addition of requirements for elevated temperature service;

c) update to butt fusion fitting requirements;

d) update to compression-type and transition fitting requirements;

e) addition of requirements for joining PA pipe and fittings; and

f) update to the fitting sampling and testing schedule.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.18:26 - Polyethylene of raised temperature resistance (PE-RT) tubing systems for pressure applications

Preface

This is the fifth edition of CSA B137.18, Polyethylene of raised temperature resistance (PE-RT) tubing systems for pressure applications. It supersedes the previous editions published in 2023, 2020, 2017, and 2013.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The following are the major changes to this edition:

a) revision to applications in the scope;

b) clarification of the bent-tube hydrostatic sustained pressure

strength test procedure; and

c) update to storage and handling and protection from short- and long-term exposure to sunlight in Annex A.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

------------------------------------------------------------------------

CSA B137.19:26 - Crosslinked polyethylene (PEX) piping systems for gas services

Preface

This is the fourth edition of CSA B137.19, Crosslinked polyethylene (PEX) piping systems for gas services. It supersedes the previous editions published in 2023, 2020, and 2017.

This Standard is to be used with the 2026 edition of CSA B137.0, which provides requirements and test methods that are common to some or all of the Standards of the CSA B137 series.

The major changes in this edition include

a) addition of PEX XX07 designation code; and

b) additional requirements for PEX XX09 materials.

This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard.

This Standard was prepared by the Technical Committee on Plastic Pressure Piping, under the jurisdiction of the Strategic Steering Committee on Construction and Civil Infrastructure, and has been formally approved by the Technical Committee.

This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group.

如果您需要的标准信息不在清单中,请将您需要的标准号发来,针对需要购买标准文件进行报价,建议单位申购,扫码添加微信,登记单位信息后进行订购

宽天下标准翻译提供国外标准翻译中文和国家标准翻译英文服务,涵盖最新版本的标准:GB、ISO、CEN、GJB、MIL、IEC、UL、BS、NF、DIN、JIS、GMW、GOST、KS、ANSI、ASTM、ASME、AWS、IEEE、API、AS/NZS、SAE、CIE、CSA、CGA、AOAC、AASHTO、NFPA、ACI等等。

查标准、看标准、买标准、译标准

需要了解更多,请添加微信:fanyi800

欢迎访问:www.kuantianxia.com

回首页,搜索你想要的文档

在首页搜索框输入关键词,快速定位资料

文库首页搜索指引 立即搜索

相关学习资料